How Replace a Kitchen Faucet – 3 Small But Important Things

If you want a new faucet in your kitchen, don’t call the plumber. Installing a kitchen faucet is easy to do as long as you have some wrenches handy. First off, remove the old one and then install this cool new fixture. It’ll make everything satisfied with its updated look for sure. This article will lead you to the solutions of how to replace a kitchen faucet cartridge step by step. Follow the guidelines for doing it by yourself.

1. Step Through Removing the Old Faucet

This is the guide you can follow to you remove kitchen faucets a new or old. The following instructions are only for removing the old faucet. So do it yourself under the following guideline.

a. Shut off Valves

For a leak-proof kitchen sink, make sure to close both the hot and cold water valves. Turn off your garbage disposal if you have one under your sink before proceeding with this step of the guide for fixing leaks.

Now open up cabinets underneath the sinks in order to find knobs. That the knobs control those two pipes respectively which are attached at opposite ends of their respective valve’s pipe or tube (the “P” trap).

After turning these knob mechanisms as they’re perpendicular opposed to parallel towards each other. Shut everything back down again by reversing them. You need to do it when finished reinserting plugs into sockets labeled “garbage disposals” and twisting screws on faucet handles.

b. Turn on your existing faucet to relieve any water pressure

If you want to protect your pipes from bursting and avoid the inconvenience of a water leak, make sure that they are dry before shutting them off. If there is any residual pressure in the plumbing system, it will be relieved by keeping some valves open for at least one hour after shut down.

c. Loosen the attached nuts to the water lines

Take your wrench and loosen the nuts that are holding your water lines together. You should be able to unscrew these hexagonal-shaped pieces with a basic adjustable wrench.

But if you need some extra help, try using an open ended or box end wrenches first before swapping over to one of those for tighter spaces. Once all loose enough in place, you can turn them by hand without much effort.

Now detach the hoses from both faucets until only two remain connected—one is going into where it attaches at the wall behind your sink. And the will have come out through either under or near where this valve used to attach itself on top of a shelf underneath it. Place something down like a bucket or towel right below each connection.

d. Use a basin wrench to remove the nuts from the faucet

Put on some gloves and remove the faucet nuts with a basin wrench. The long-handled tool makes it easier to reach under your sink. So adjust its length until you can grab one of those pesky little nuts that are just out of arm’s reach and turn them counterclockwise until they loosen fully.

If you don’t have any tools in stock at home already, head over to your local hardware store for this nifty purchase today.

e. Pull the faucet out of the sink and clean any grime or residue

Stainless steel sinks are sleek and modern, but they can be difficult to clean. Here’s how you take care of a stubborn stain on your sink:

Remove the faucet from the hole in your sink. There might be some grime or residue around it that needs removing. Use an old washcloth with multipurpose cleaner to lift up any debris left by previous installation.

You may need more than one wipe if layers have built up over time. Let the cleaner sit for 1 minute before scrubbing again. Letting these cleaners work their magic will leave you feeling like new after a deep-cleanse. So don’t forget them next time something is giving off an odor or buildup.

However, carefully do it according to the instructions to remove the old faucet. This guide is a help while you are learning to how replace a kitchen faucet. 

2. Installing the New Faucet

The guides below will help you to setup a new kitchen faucet. Because you already have removed the old one. Now see how replace a kitchen faucet that looks good for your kitchen. Also if want to know about faucet history go here.

Assemble a new faucet

Assemble the supplies you need first. Choose one that matches your style and follow these following simple steps to install a new faucet:

• wrap three layers of Teflon tape around the threads in order for water not to leak;
• screw on supply tubes with an adjustable wrench by hand without any force
• find a matching color thread cap before attaching it all together
• read instructions inside package carefully because they will show you which way up each part should be rotated when assembling

Put off additional holes in your sink with trim rings or a deck plate

If you’ve got one or two extra holes in your sink, cover them up with trim rings. If there is more than that, it might be a good idea to put on the deck plate provided by the manufacturer of whatever faucet is currently installed.

You need to make sure everything stays level before securing it underneath your sink. So just use an adjustable wrench and tighten those nuts very tightly.

Deck plates are the sheets of metal that lie on top and cover your sink. There is a different type for each kind of material.

So choose it carefully. Trim rings will give you an extra splash guard to stop water from getting outside or underneath it when filling up pots with dishes in them.

Deck Plates can be purchased at any local home improvement store. But there are some things to consider before purchasing anything just yet. The first thing you need to think about is if this project needs more than one hole?

For example, do you have 1 hole where your faucet currently sits or do you want 3 holes instead? This article on how replace a kitchen faucet won’t help you answer those questions. Because you guy know well the present condition of your kitchen faucet replacement project.

Feeding the supply tubes into the hole to position the new faucet

Are you ready to install a new faucet? If so, feed the supply tubes into the hole and position it as needed. There are 2 types—those that have twin handles require 3-holes, while single handle ones only need 1 hole for alignment purposes. Slowly put them in to avoid any sharp edges on the inside which might cut through them.

This is all about, align now over your sink’s holes, and feed one tube through at a time to manage them well.

Then lower onto sink after all are in place. Be careful not to cut these fragile pipes by feeding slowly. Do it only then, if there is anything sharp that might get in their way on the inside of this tight space.

Secure the faucet by tightening the nuts with a basin wrench

The best way to install a new faucet is by turning it into the sink and securing with nuts. Tighten each nut until they are secure using your basin wrench, but not too tight.

Have someone hold the faucet firm from the above. So you don’t have to worry about touching any slippery surfaces while installing. You can also use dish soap as lubricant for installation if needed during installation.

Connect the sink sprayer to the faucet

The sprayer is a great way to rinse any food left on dishes or plates. So connect the sink sprayer if you have one and set it in place before screwing the mounting nut into your faucet hole to attach it securely.

Attach an end of hose that’s connected at bottom port of your sink. Then push it until fixed together with other side. This type will vary depending on which kind you need for yours. But they all work basically the same. And at this moment, just feed through base from water supply and twist fountain head onto top connective valve-like part as you are giving pressure when turned it on.

Attaching water lines to the faucet supply hoses

There are many steps to plumbing that you may not know about. When it comes time to fix a leak, make sure the right water line is connected first. It is done by holding up either hot or cold supply hoses from the faucet and placing them next to your respective garbage disposal—eventually if they were disconnected earlier.

The next step is, screw in each nut finger tight. You can also wrap 3 layers of Teflon tape around their threads for additional protection against leaks.

3. Cleaning Out the Debris Through Faucet Mouth

Unscrew the aerator from the end of the faucet

Unscrew the aerator from one end of your faucet. The attachment is a thin metal mesh that controls water flow and can be located on either side of your kitchen sink or in front near where you wash dishes. To remove it, turn counterclockwise and pull gently to take it off without scratching any surfaces.

Turn the water valves back on

If you are fixing a leaky valve, use your wrench to tighten the nuts that hold it snugly in place. To test for leaks at this point, make sure there is nothing blocking any of the lines and valves before turning on water supply again.

If necessary, rotate all connections. So they’re once more aligned with each other when done tightening bolts.

Once everything seems well-secured after testing them out one last time, turn off the valve again. And, then wrap up by putting down protection beneath your leaking valves until they stop dripping completely at the moment.

Turn on your faucet for 2-3 minutes to let out the bad water

To keep your faucet running smoothly, it is important to routinely clean the valves. Start it by turning on both handles for a couple of minutes so that any debris or dust inside gets flushed out.

If you have 2 handles, turn them both on and let water run through all lines before shutting off one handle at a time. It will help to flush each line separately and clear the bad water through the faucet mouth.

Replacing the aerator again

To turn off your faucet, unscrew the aerator clockwise and screw it back into place. Once you reattach it to the pipes, grab a glass of water then push down on the handle until all air bubbles are removed from inside. The way you have learnt a lot from the search of “how replace a kitchen faucet”

The Outline

 How replace a kitchen faucet? Yes, you already have known everything in this post here. However, after following the steps in this blog post, you should have a new kitchen faucet installed. You may need to get some help from someone else if you are not comfortable with any of these tasks. We hope that we’ve answered all your questions and given you confidence when it comes time to replace your old sink fixture. If there is anything left unclear or unanswered, please feel free to search more online. Happy plumbing!